I decoded guru meditation errors

thank you for this link, but i not problem in flash i problem in create new framework and in this link not defined tutorial for create framework esp32

For the last test, instead of wsl windows, I want to test in Linux virtual box, if it gives the same error again, I will say goodbye to espruino.

But if I could, I would make powerful style libraries for it, because I'm good at esp-idf, especially on screen to improve its speed.

read this flashing detail

https://github.com/espruino/Espruino/blob/master/targets/esp32/README_flash.txt

and this too

http://www.espruino.com/ESP32

this describes the buid process

https://github.com/espruino/Espruino/blob/master/README_Building.md

before flash new firmware run

make erase_flash

https://github.com/espruino/Espruino/blob/f173832d935f87033f560b88de4af4f3a0fa1cde/make/targets/ESP32.make#L43

what is the reason for building your own firmware?

esp32 firmware is very little maintained over the last few years.

check the issue list https://github.com/espruino/Espruino/issues/1777

So I took some ESP32 board with wroom32 module from drawer, cloned current Espruino repo and had zero issuses with building and running Espruino

git clone https://github.com/espruino/Espruino
cd Espruino
. scripts/provision.sh ESP32
make -j BOARD=ESP32 RELEASE=1
make -j BOARD=ESP32 RELEASE=1 flash

And it flashed the board just fine and espruino runs. It does print same PSRAM failed message (there is no psram in wroom32 module) but it works pretty fine

ets Jun  8 2016 00:22:57

rst:0xc (SW_CPU_RESET),boot:0x13 (SPI_FAST_FLASH_BOOT)
configsip: 0, SPIWP:0xee
clk_drv:0x00,q_drv:0x00,d_drv:0x00,cs0_drv:0x00,hd_drv:0x00,wp_drv:0x00
mode:DIO, clock div:2
load:0x3fff0018,len:4
load:0x3fff001c,len:2984
load:0x40078000,len:10700
load:0x40080400,len:5236
entry 0x40080658
E (29) boot: ota data partition invalid, falling back to factory
E (326) psram: PSRAM ID read error: 0xffffffff
E (326) spiram: SPI RAM enabled but initialization failed. Bailing out.
E (326) spiram: SPI RAM not initialized

 ____                 _ 
|  __|___ ___ ___ _ _|_|___ ___ 
|  __|_ -| . |  _| | | |   | . |
|____|___|  _|_| |___|_|_|_|___|
         |_| espruino.com
 2v16.152 (c) 2021 G.Williams

Espruino is Open Source. Our work is supported
only by sales of official boards and donations:
http://espruino.com/Donate

WARNING: Wifi:startMDNS - espressif
>

it's interesting. Until now, I have not seen this command model for making firmware anywhere

make -j BOARD=ESP32 RELEASE=1
make -j BOARD=ESP32 RELEASE=1 flash

I mean (make -j), I will definitely test that as well

Have you flashed the javascript code to see if it is saved and executable?

Adding more features and improving its speed in (screen, SPI) and adding more and useful commands. I'm currently working with esp idf, but I'm primarily a javascript developer. I like to design mostly with javascript, but esp idf is great too.

And

With esp idf I wrote code that is really fast on STXXXX and ILIXXXX series displays and works perfectly with 16-bit RGB colors without slowing down. I want to add these features to Espruino.

I already tested all these links. But unfortunately, Espruino does not work well with me, however, thank you for sending these links