Pax-Instruments PI13264 132*64 LCD?

Taking Gordon's code as a template, I suppose it would look something like the code below. I pulled the init sequence from u8g_dev_st7567_pi13264.c and the define statements from u8g.h.

NOTE: The code block rendering engine turns hash marks into links. In the define statements below you'll have to remove all the forward slashes.

// I grabbed these define statements from u8g.h in the u8glib library
// using this command "grep -ir U8G_ESC_* utility/u8g.h"
  \#define U8G_ESC_DLY(x) 255, ((x) & 0x7f)
  \#define U8G_ESC_CS(x) 255, (0xd0 | ((x)&0x0f))
  \#define U8G_ESC_ADR(x) 255, (0xe0 | ((x)&0x0f))
  \#define U8G_ESC_RST(x) 255, (0xc0 | ((x)&0x0f))
  \#define U8G_ESC_VCC(x) 255, (0xbe | ((x)&0x01))
  \#define U8G_ESC_END 255, 254
  \#define U8G_ESC_255 255, 255

var exports={};
exports.connect = function(/*=SPI*/_spi, /*=PIN*/_dc, /*=PIN*/_ce, /*=PIN*/_rst, callback) {
  var LCD = Graphics.createArrayBuffer(128,64,1,{ver­tical_byte:true});
  var spi = _spi;
  var dc = _dc;
  var ce = _ce;
  var rst = _rst;
  setTimeout(function() {
    digitalWrite(dc,0); // cmd
    digitalPulse(rst, 0, 10); // pulse reset low
    
    setTimeout(function() {      
      spi.write([
     U8G_ESC_CS(0),    /* disable chip */
      U8G_ESC_ADR(0),   /* instruction mode */
     U8G_ESC_CS(1),    /* enable chip */
    U8G_ESC_RST(15),  /* do reset low pulse with (15*16)+2 milliseconds (=maximum delay)*/
  0x0a3,		    /* 0x0a3: LCD bias 1/9 (suggested for the pi13264) */
  0x0a1,		    /* 0x0a1: ADC set to reverse (suggested for the pi13264) */
  0x0c0,            /* common output mode: set scan direction normal operation/SHL Select, 0x0c0 --> SHL = 0, normal, 0x0c8 --> SHL = 1 */
  0x040,		    /* set display start line */
  0x028 | 0x04,     /* power control: turn on voltage converter */
      U8G_ESC_DLY(50),  /* delay 50 ms */
  0x028 | 0x06,     /* power control: turn on voltage regulator */
      U8G_ESC_DLY(50),  /* delay 50 ms */
  0x028 | 0x07,     /* power control: turn on voltage follower */
     U8G_ESC_DLY(50),  /* delay 50 ms */
  0x026,		    /* set V0 voltage resistor ratio to 6 */
  0x0a6,            /* display normal, bit val 0: LCD pixel off. */
  0x0C0,		    /* set contrast */
  0x018,		    /* contrast value*/
  /*0x0ac,*/        /* indicator */
  /*0x000,*/        /* disable */
  0x0af,            /* display on */
     U8G_ESC_DLY(100), /* delay 100 ms */
  0x0a5,		    /* display all points, ST7565 */
     U8G_ESC_DLY(100), /* delay 100 ms */
      U8G_ESC_DLY(100), /* delay 100 ms */
  0x0a4,		    /* normal display */
     U8G_ESC_CS(0),    /* disable chip */
      U8G_ESC_END       /* end of sequence */
        ], ce); 
      if (callback!==undefined) callback();
    }, 100);
  }, 100);
  LCD.flip = function () {
    for (var y=0;y<8;y++) {
      digitalWrite(dc,0); // cmd
      spi.write([0xB0|y/* page */,0x00/* col lower*/,0x10/* col upper*/],ce); 
      digitalWrite(dc,1); // data
      spi.write(new Uint8Array(this.buffer, 128*y, 128), ce);
    }
  };
  return LCD;
};
// or whatever your pins are:
SPI1.setup({ sck:B3, mosi:B5 });
var g = exports.connect(SPI1,B6,B7,B8, function() {
  g.clear();
  g.drawString("Hello",0,0);
  g.drawLine(0,10,84,10);
  g.flip();
});